Incoloy 800/ 800H/ 800HT Instrumentation Valves
Introduction
Kalpataru piping Is one of the leading manufacturer, suppliers, exporter, stockist of Incoloy 800/ 800H/ 800HT
Specification
|
Grades |
: |
Incoloy 800 – UNS N08800, Incoloy 800H / HT – UNS N08810/N08811 |
|
Standards |
: |
ASTM, ASME and API |
|
Specifications |
: |
ASTM B 407, 514, 515/ ASME SB 407, 514, 515 |
|
Size |
: |
15″NB TO 150″NB IN |
|
Length |
: |
Within 13500mm |
|
Type |
: |
Seamless / ERW / Welded / Fabricated / CDW |
|
Form |
: |
Round, Square, Rectangular, Coiled Tubes, “U” Shape, Pancake Coils, Hydraulic Tubes |
|
End |
: |
Plain End, Beveled End, Threaded |
Chemical Properties of Incoloy 800/ 800H/ 800HT Valves:
|
Incoloy 800 |
Ni |
Fe |
Cr |
Cu |
Ti |
Al |
C |
Mn |
S |
Si |
|
30.0-35.0 |
39.5 min |
19.0-23.0 |
.75 max |
.15-.60 |
.15-.60 |
.1 max |
1.5 max |
.015 max |
1.0 max |
|
|
Incoloy 800H |
Ni |
Fe |
Cr |
Cu |
Ti |
Al |
C |
Mn |
S |
Si |
|
30.0-35.0 |
39.5 min |
19.0-23.0 |
.75 max |
.15-.60 |
.15-.60 |
.05-.10 max |
1.5 max |
.015 max |
1.0 max |
|
|
Incoloy 800HT |
Ni |
Fe |
Cr |
Cu |
Ti |
Al |
C |
Mn |
S |
Si |
|
30.0-35.0 |
39.5 min |
19.0-23.0 |
.75 max |
.25-.60 |
.85-1.20 |
.06-.10 max |
1.5 max |
.015 max |
1.0 max |
Mechanical Properties of Incoloy 800/ 800H/ 800HT Valves:
|
Grade |
Density |
Melting Point |
Tensile Strength |
Yield Strength (0.2%Offset) |
Elongation |
|
Incoloy 800 |
7.94 g/cm3 |
1350-1400 ℃ |
500 |
205 |
30 – 35 % |
|
Incoloy 800H |
7.94 g/cm3 |
1350-1400℃ |
500 |
200 |
30 – 35 % |
|
Incoloy 800HT |
7.94 g/cm3 |
1350-1400℃ |
500 |
200 |
30 – 35 % |
Related Products
- Incoloy 800/800H/800T Instrumentation Valves
- Incoloy 800/800H/800T Filler Wire
- Incoloy 800/800H/800T Long Radius Bends
- Incoloy 800/800H/800T Pipes Spools
- Incoloy 800/800H/800T Wiremesh
- Incoloy 825 Instrumentation Valves
- Incoloy 825 Filler Wire
- Incoloy 825 Long Radius Bends
- Incoloy 825 Pipes Spools
- Incoloy 825 Wiremesh
FAQ’s About Monel Flanges
What is the maximum service temperature for Monel 400 flanges?
Monel 400 flanges can be used up to approximately 550°C (1022°F) in non-oxidizing conditions, making them suitable for high-temperature chemical processing and steam applications.
Can Monel flanges be used with hydrofluoric acid?
Yes. Monel 400 is the industry-standard material for handling hydrofluoric acid at nearly all concentrations and temperatures in de-aerated conditions, which is why it is widely specified for HF alkylation units in refineries.
What is the difference between ASTM B564 and ASME SB564?
ASTM B564 is issued by ASTM International, while ASME SB564 is the equivalent specification adopted by the ASME Boiler and Pressure Vessel Code. The two are technically identical for Monel forged fittings and flanges; ASME SB564 is typically referenced for boiler and pressure-vessel code compliance.
Do you supply Mill Test Certificates with Monel flanges?
Yes. Every Monel flange from Kalpataru Piping is supplied with an EN10204 Type 3.1 Mill Test Certificate as standard. Type 3.2 third-party witnessed certification and additional QAP or radiography documentation can be arranged on request.
What is the typical lead time for Monel flanges?
Standard sizes in Monel 400 and Monel K500 are typically available ex-stock or within a short lead time; custom sizes, pressure classes, or Type 3.2 certification requirements may extend delivery. Contact our sales team with your specification for an accurate lead-time estimate.
What is the difference between a Monel Slip-On Flange and a Monel Weld Neck Flange?
A slip-on flange slides over the pipe end and is fillet-welded on both sides, making it easier and faster to install at lower pressure ratings. A weld neck flange has a tapered hub that is butt-welded to the pipe, giving superior stress distribution and making it the preferred choice for high-pressure, high-temperature, and cyclic-load services.
