Incoloy 825 Plates And Sheets
Introduction
Kalpataru piping is one of the leading Manufacturer, Supplier, Exporter of incoloy 825 Plates/Sheets in India. Incoloy 825 Plates/ Sheets are incoloy-chromium alloy with an addition of aluminum for outstanding resistance to oxidation and other forms of high temperature corrosion. These incoloy 825 sheets (UNS N08825) are used for Heat treating muffles and retorts, Catalyst support grids in nitric acid production, Radiant tubes, Steam super-heater tube supports, and more. incoloy Alloy 825 Plates are also used in fabricated combustion chambers, tube supports and ash trays in the power generation industry. incoloy 825 Plate is a solid solution incoloy chromium heat resisting alloy which gives outstanding performance at temperatures up to about 1825°C. incoloy 825 Plate also has good aqueous corrosion resistance due to the high incoloy content in combination with chromium. Strength and toughneincoloy are good, and are retained during extended service at high temperature. incoloy 825 Sheet has good resistance to nitriding in ammonia, and is only outperformed by incoloy 825 Coil in this application. incoloy 825 Rolling Sheet has good strength, ductility and toughness of incoloy, and can be used at cryogenic temperatures. incoloy 825 Flat Sheet is a incoloy alloy and available in the various forms including incoloy Alloy 825 Plate & incoloy 825 Perforated Plate etc. incoloy 825 Rolling Plate has good high temperature strength and retains its ductility after long service exposure, with good corrosion resistance under oxidizing conditions. incoloy 825 Hot rolled Plate is very resistant to high-temperature oxidation – up to 2825 º F – and its also has good resistance to aqueous corrosion. incoloy 825 Clad Plates are suitable to use at elevated temperatures. We offer incoloy 825 plate, incoloy 825 sheet are in different sizes, specifications and shapes as per demands of our esteemed customers. The Incoloy 825 plate & sheet weight calculator allows you to calculate the approximate weight of SB 424 plates and sheets in different thicknesses.
Incoloy 825 Sheet, Plate Specifications
| Specifications | : | ASTM / ASME SB 424 |
| Size | : | 1000 mm x 2000 mm, 1220 mm x 2440 mm, 1500 mm x 3000 mm, 2000 mm x 2000 mm, 2000 mm x 4000 mm |
| Thickness | : | 0.1mm to 12 mm Thk |
| Form | : | Coils, Foils, Rolls, Plain Sheet, Shim Sheet, Strip, Flats, Blank (Circle), Ring (Flange) |
| Finish | : | Hot rolled plate (HR), Cold rolled sheet (CR), 2B, 2D, BA NO(8), SATIN (Met with Plastic Coated) |
| Hardness | : | Soft, Hard, Half Hard, Quarter Hard, Spring Hard etc. |
Incoloy 825 Plate, Sheet Chemical Composition
| Grade | C | Mn | Si | S | Cu | Fe | Ni | Cr | Al | Ti |
| 825 | 0.05 max | 1.00 max | 0.5 max | 0.03 max | 1.50 – 3.00 | 22.00 min | 38.00 – 46.00 | 19.50 – 23.50 | 0.02 max | 0.06 – 1.20 |
Alloy 825 Sheets, Plates Mechanical Properties
| Element | Density | Melting Point | Tensile Strength | Yield Strength (0.2%Offset) | Elongation |
| 825 | 8.14 g/cm3 | 1400 °C (2550 °F) | Psi – 80,000 , MPa – 550 | Psi – 32,000 , MPa – 220 | 30 % |
Equivalent Grades for 825 Incoloy Sheets & Plates
| STANDARD | WERKSTOFF NR. | UNS | JIS | BS | GOST | AFNOR | EN | OR |
| Incoloy 825 | 2.4858 | N08825 | NCF 825 | NA 16 | ЭП703 | NFE30C20DUM | NiCr21Mo | XH38BT |
Related Products
- Incoloy 800/800H/800T Instrumentation Valves
- Incoloy 800/800H/800T Filler Wire
- Incoloy 800/800H/800T Long Radius Bends
- Incoloy 800/800H/800T Pipes Spools
- Incoloy 800/800H/800T Wiremesh
- Incoloy 825 Instrumentation Valves
- Incoloy 825 Filler Wire
- Incoloy 825 Long Radius Bends
- Incoloy 825 Pipes Spools
- Incoloy 825 Wiremesh
Frequently Asked Questions
What's the difference between Monel 400 and Monel K500 fasteners?
Monel 400 is the standard, lower-cost grade for general corrosion resistance in chemical, marine, and acid service. Monel K500 is age-hardened for roughly double the tensile strength, at a 30–50% cost premium, and earns that premium on high-load or wear applications like shafting and pump components. See our full comparison on the Monel 400 Fasteners page.
Which Monel grade should I use for marine fasteners?
Monel 400 covers the vast majority of marine fastening needs — seawater piping, deck hardware, and general corrosion resistance. Reach for Monel K500 specifically when the application also carries a real mechanical load, like propeller shafting or pump hardware.
Do you supply custom or coated Monel fasteners?
Yes — custom head marking, thread locking compounds, and surface coatings are all available on request, in addition to standard mill-finish fasteners.
What is the minimum order quantity for Monel fasteners?
We run zero MOQ across both grades. Standard sizes are ex-stock in Mumbai for fast dispatch; anything outside standard stock is manufactured to order with no minimum quantity requirement.
What certificates come standard with Monel fasteners?
Every order ships with an EN 10204 3.1 mill test certificate. PMI, third-party inspection (TPI), and NABL-accredited lab reports are available on request for critical applications.
What is the HS code for Monel fasteners?
Generally 7318.15.00, though it's worth confirming the exact classification with your customs broker since it can vary slightly by destination country.
What industries typically use Monel fasteners?
Chemical and petrochemical processing, oil and gas (including sour service), marine and shipbuilding, and defense/aerospace account for the large majority of demand, with occasional specialty use in coastal construction hardware.
What payment and delivery terms do you offer?
We accept LC, TT/wire transfer, and cheque, with export-grade packaging and dispatch from Mumbai or Kalamboli ports. See the Packaging, Payment & Delivery section above for details.
Need Monel 400 Wire Mesh You Can Actually Rely On?
Tell us your mesh count, weave, and quantity, and we'll get you a quote with a real lead time — not a generic price list. Specifying a full system? Run the numbers first with our pipe & tube weight calculator or plates & sheets weight calculator.
